The usual answer is three beads for a one-inch stamp. That is a good place to start, but it is not a fixed rule, because sealing wax beads are not a standard size. This guide gives you sensible starting amounts, shows you how to find the exact number for your own stamp and wax in a few minutes, and helps you estimate how many beads to buy for a project.
Starting amounts by stamp size
Use these as a first test, not as a guarantee.
| Stamp head | Starting amount |
|---|---|
| 25 mm (about 1 inch) | 3 beads |
| 30 mm (about 1 1/8 inch) | 4 beads |
| Larger than 30 mm | Start with 5 and test |
If you look at several sellers, you will see different numbers. Recommendations for a one-inch stamp range from two beads to five, and for a 30 mm stamp from four to seven. Nobody is wrong. They are describing different beads and different styles of seal.
Why the number varies
Bead size. Octagonal beads from one maker can be noticeably larger than those from another. Shaped beads, such as hearts, stars and flowers, are not necessarily the same size as standard octagons, so test before you count on a number.
The rim you want. Some people like a seal that barely extends past the design. Others want a wide, organic border of wax around it. A generous rim can take one or two extra beads.
How hard you press. Firm pressure pushes wax outward and makes a thinner, wider seal. Light pressure leaves a thicker, smaller one from the same amount of wax.
The depth of the engraving. A deeply cut design holds more wax in the stamp itself.
What is left in the spoon. A little wax always stays behind. With a clean spoon the first seal of a session may come out slightly smaller than the rest.
How to find your number in five minutes
Do this once for each stamp and each type of bead you own.
- Lay out a sheet of parchment paper or a silicone mat.
- Melt the starting amount from the table and make a seal.
- Look at the result. The design should be fully formed, with an even rim of wax all the way around and no paper showing through.
- If the rim is missing on one side or the seal looks thin, add one bead and try again.
- If wax squeezes far beyond the stamp or the seal is thicker than you want, remove one bead.
- When you get a seal you like, write the number down. A small note inside the lid of your bead box saves you from repeating the test.
Test seals are not wasted. Peel them off the parchment and remelt them.
Mixing colors
For a marbled seal, keep the total number of beads the same and split it between colors. With a three-bead seal, two beads of the main color and one of the accent gives a visible swirl without muddying the result. Let the beads melt, drag a toothpick through once, and pour. Stirring thoroughly blends the colors into a single new shade, which can be nice too, but is a different effect.
How many beads should you buy?
Once you know your number, the math is simple:
Seals needed × beads per seal = beads needed. Then add a margin for practice and mistakes. Fifteen to twenty percent is reasonable for a first project.
Some examples using three beads per seal:
| Project | Seals | Beads for seals | With about 20% extra |
|---|---|---|---|
| A few letters a month | 10 | 30 | About 36 |
| Holiday cards | 40 | 120 | About 145 |
| Wedding invitations | 100 | 300 | About 360 |
| Wedding invitations plus reply envelopes | 200 | 600 | About 720 |
With a four-bead seal, multiply by four instead. Bead packs are commonly sold in counts of about 100 and up, and some are sold by weight, in which case the listing normally gives an approximate count. Check the number in the product description and compare it with your total.
For a wedding or another event, order all the wax in one color at the same time. A second order placed weeks later may not match the first exactly.
Getting the most from each bead
Melt only what you need. Count the beads into the spoon for each seal. Melting a large amount and trying to pour several seals from one spoonful usually leads to uneven sizes and wax that cools before you finish.
Scrape the spoon while it is warm. The film left in the spoon can be pushed into the next melt when you are using the same color.
Save your rejects. A seal that did not come out well can go straight back in the spoon and be melted again.
Do not overheat. Take the spoon off the heat as soon as the last lump melts. Wax that is too hot runs thin, spreads too far, and gives you a wide, flat seal that looks like it needed more beads when it really needed less heat.
Beads compared with other forms of wax
If you are working in large quantities, glue gun sticks are faster than beads, because there is no melting step between seals. Beads are better when you want precise amounts, color blends, or only a handful of seals at a time. Many people use beads to work out the look they want, then switch to glue gun sticks in the same color for the production run. Our guide to beads, sticks and glue gun wax covers the differences in detail.
Frequently asked questions
How long does it take to melt a few beads? Over a tea light, typically 30 to 60 seconds. A warmer that holds the spoon close to the flame is quicker than holding it by hand.
How should beads be stored? In a closed container, away from heat and direct sunlight, so they do not soften and stick together.
See our sealing wax beads for single colors, assorted boxes and larger refill packs.