How to Clean a Wax Seal Stamp and Melting Spoon

Wax seal tools are simple, and they last for years with very little care. The two things that cause trouble are wax left in the engraving of the stamp, which blurs the next impression, and residue in the spoon, which muddies your colors. Both are easy to deal with. This guide covers routine cleaning, how to remove stuck wax, and how to store your tools.

Cleaning the stamp head

After a normal session

Most of the time a brass stamp head needs no cleaning at all. If the stamp was cool and you waited for the wax to set, it lifts away clean. Wipe the face with a soft dry cloth, make sure it is dry, and put it away.

When wax is stuck in the design

Wax stays behind in the engraving when the stamp was too warm, when it was lifted before the wax had set, or when the wax was extremely hot and thin. Try these methods in order, starting with the gentlest.

1. Let it harden and pick it out. Rest the stamp on an ice pack until the wax is completely hard, then lift it out with a wooden toothpick. Use wood or plastic, never a metal pin or knife, which can scratch the engraving.

2. Stamp it out. Make a fresh seal on parchment paper with the stamp well chilled. The new wax often bonds to the old residue and pulls it out as the seal sets. You may need to repeat this once or twice. Stamp makers recommend this trick, and it costs you only a few beads that can be remelted.

3. Wash it. For stubborn buildup, soak the metal head in warm, soapy water for a few minutes, then scrub the engraving gently with a soft toothbrush. Rinse and dry thoroughly with a soft cloth. If the head unscrews from the handle, remove it first so the wood stays dry. Rubbing alcohol on a cotton swab is another option for the last traces.

What to avoid

  • Abrasives. Scouring pads, steel wool and gritty cleaners can wear down fine engraved lines.
  • Sharp metal tools. A scratch in the design will show up in every seal afterward.
  • Soaking wooden handles. Water can swell or crack the wood and loosen the fitting.
  • Open flame on the stamp. Heating the head to melt wax out can leave soot in the design and makes the stamp too hot to use for a while.

Tarnish

Brass darkens naturally with time and handling. A deeper, aged color does not affect the quality of your seals. If you prefer the bright finish, a jewelry polishing cloth restores it. Polish the sides and the back of the head, and go lightly over the engraved face.

Cleaning the melting spoon

Removing leftover wax

A thin layer of wax remains in the spoon after each pour. If your next seal is the same color, leave it there; it will melt into the new beads.

To change colors:

  1. Warm the spoon briefly so the leftover wax softens.
  2. Take it off the heat and wipe the bowl with a folded paper towel. Hold the towel with care, because the metal is hot. Tongs or a thick fold of towel keep your fingers away from the bowl.
  3. Repeat until the towel comes away clean.

Going from a light color to a dark one, a trace of the old wax does not matter. Going from dark to light, clean thoroughly, or the first seal will come out tinted. Many people keep two spoons, one for dark colors and one for light and metallic ones, and skip the problem entirely.

A non-stick spoon is easier still, since cooled wax lets go of the surface more readily. Soft silicone scraping tools are useful for lifting out what remains without scratching the bowl.

Removing soot

The black film on the underside of a metal spoon is soot from the candle flame. It is harmless to the spoon, but it rubs off on hands and paper and can drop flecks into the wax if it creeps over the rim.

Soot is normal. Wipe the underside with a dry paper towel once the spoon has cooled, and do it after every session so it does not build up. For a heavier layer, wash the spoon with warm water and dish soap and dry it well. To reduce soot in the first place, hold the spoon just outside the flame instead of down in it. A warmer that holds the spoon at a fixed height helps for the same reason.

What to do with waste wax

Never pour melted wax into a sink or drain. It hardens in the pipe and can cause a blockage. Pour leftover wax onto parchment paper, let it cool, and either save it for remelting or put it in the trash.

Cleaning a glue gun used for wax

If you use glue gun sealing wax, keep one gun for wax only. To change colors, makers suggest clearing the chamber before loading the new color, or simply keeping a separate gun for each color you use often. Squeeze the first pours onto parchment until the color runs pure; the mixed wax makes marbled seals, so it need not be thrown away.

Do not try to dig wax out of the nozzle with a tool while the gun is hot, and do not immerse the gun in water. Unplug it and let it cool before wiping the outside. Drips on the nozzle peel off once they are cold.

Cleaning mats and work surfaces

Silicone mats and parchment paper release wax easily once it is cold. Peel or flex and the drips pop off. For wax on a table, let it harden fully and lift it with a plastic scraper or the edge of an old card. Wax on fabric is harder to remove, which is a good reason to cover your work area before you start.

Storage

  • Dry everything first. Do not put brass away damp.
  • Protect the engraved face. Store stamp heads so the design is not rubbing against other metal. A small pouch, a divided box, or the original packaging works.
  • Keep wax cool. Beads and sticks soften in heat. Store them away from windows, radiators and hot cars, in a closed container so they do not collect dust.
  • Keep sets together. A box with the stamp, spoon, a few tea lights and a square of parchment means you can sit down and seal without hunting for parts.

A quick routine

After each session:

  1. Chill the stamp, check the engraving, and remove any wax.
  2. Wipe the stamp dry.
  3. Wipe out the spoon while it is still slightly warm.
  4. Once it is cool, wipe soot from the underside.
  5. Collect leftover wax for next time.

It takes about two minutes, and it means the next seal starts with clean tools.

Need a spare spoon for light colors, or a non-stick one? See our wax seal warmers, spoons and tools.

Back to blog